TITLE

Examination of Shape Error of Outer Cylindrical Surfaces Machined by Environmentally Friendly Way

pdf PDF

ABSTRACT

The paper deals with experimental examination of the machining of the cylindrical workpieces. The purpose of this paper was to obtain a comprehensive understanding of the relation between cutting data (cutting speed, feed rate), parameters of coolants and lubricants (viscosity, volume per minute), and error of machined cylindrical workpiece in terms of peak to valley cylindricity deviation, peak to reference cylindricity deviation, and reference to valley cylindricity deviation during “outer boring” with a carbide insert in AISI 1045 steel. Full factorial experiment design was used in the study. The kinematics and rigidity of the machining examined here differs from the usual machining. In our study, the cylindrical workpiece is standing on the milling machine, and a cutting tool having single point cutting edge makes the rotating movement and the feed as well. Our aim is to determine empirical expressions between the technological parameters set at machining and the geometrical shapes error. Based on the examinations, the appropriate parameter combination can be selected.

KEYWORDS

Environmentally conscious machining, cylindricity error, Factorial Experiment Design

REFERENCES

[1] Zheng, P., Wang, H., Sang, Z., Zhong, R.Y., Liu, Y., Liu, C., Mubarok, K., Yu, S., Xu, X.: Smart manufacturing systems for Industry 4.0: Conceptual framework, scenarios, and future perspectives, Frontiers of Mechanical Engineering, 2018, pp. 1-14.

[2] Hegab, H.A., Darras, B., Kishawy, H.A., Towards sustainability assessment of machining processes, Journal of Cleaner Production, Vol.170, 2018, pp. 694-703

[3] Ghani, J.A., Rizal, M., Haron, C.H.C., Performance of green machining: a comparative study of turning ductile cast iron FCD700, J. Clean. Prod., Vol.85, 2014, pp. 289-292.

[4] Mulyadi, I.H., Balogun, V.A., Mativenga, P.T., Environmental performance evaluation of different cutting environments when milling H13 tool steel, J. Clean. Prod., Vol.108 (A), 2015, pp. 110-120.

[5] Sarıkaya, M., Yılmaz, V., Gullu, A., Analysis of cutting parameters and cooling/lubrication methods for sustainable machining in turning of Haynes 25 superalloy, J. Clean. Prod., Vol.133, 2016, pp. 172-181.

[6] Cassin, C., Boothroyd, G., Lubrication action of cutting fluids, J. Mech. Eng. Sci., Vol.7, No.1, 1965, pp. 67-81.

[7] Alexander, A., Varadarajan, A.S., Philip, P.K., Hard turning with minimum cutting fluid: a viable green alternative on the shop floor. In: Proceedings of the 18th AIMTDR, 1998, pp. 152-155.

[8] Sreejith, P.S., Ngoi, B.K.A., Dry machining: machining of the future, J. Mater. Process. Technol, Vol.101, 2000.

[9] Kuram, E., Ozcelik, B., Demirbas, E., Sık, E., Effects of the Cutting Fluid Types and Cutting Parameters on Surface Roughness and Thrust Force, World Congress on Engineering, Vol.2, 2010.

[10] Gajrani, K.K., Ram, D., Sankar, M.R., Biodegradation and hard machining performance comparison of eco-friendly cutting fluid and mineral oil using flood cooling and minimum quantity cutting fluid techniques, J. Clean. Prod., Vol.165, 2017, pp. 1420-1435

[11] John, J., Bhattacharya, M., Raynor, P., Emulsions containing vegetable oils for cutting fluid application, Colloids Surf, A Physicochem. Eng. Asp., Vol.237, 2004, pp. 141-150.

[12] Gajrani, K.K., Ravi Sankar, M., Past and current status of eco-friendly vegetable oil based metal cutting fluids, Mater. Today Proc., Vol.4, No.2A, 2017, pp. 3786-3795.

[13] Klocke, F., Eisennblatter, G., Dry cutting, CIRP Ann. Manuf. Technol., Vol.46, No.2, 1997, pp. 519-526.

[14] Byrne, G., Scholta, E., Environmentally clean machining processes strategic approach, CIRP Ann. Manuf. Technol., Vol.42, No.1, 1993, pp. 471-474.

[15] Devillez, A., Coz, G.L., Dominiak, S., Dudzinski, D., Dry machining of Inconel 718, workpiece surface integrity, J. Mater. Process. Technol., Vol.211, 2011, pp. 1590-1598.

[16] Jaharah, A.G., Choudhury, I.A., Masjuki, H.H., Hassan, C.H.C., Surface integrity of AISI H13 tool steel in end milling process, Int. J. Mech. Mater. Eng., Vol.4, 2009, pp. 88-92.

[17] Galanis, N.I., Manolakos, D.E., Vaxevanidis, N.M., Comparison between dry and wet machining of stainless steel. In: Proceedings of the 3rd International Conference on Manufacturing Engineering (ICMEN), third ed. Chalkidiki, Greece, 2008.

[18] Khan, A., Maity, K., Influence of cutting speed and cooling method on the machinability of commercially pure titanium (CP-Ti) grade II, J. of Manuf. Process., Vol.31, 2018, pp. 650–661.

[19] Sarma, D.K., Dixit, U.S., A comparison of dry and air-cooled turning of grey cast iron with mixed oxide ceramic tool, J. Mater. Process. Technol., Vol.190, 2007, pp. 160-172.

[20] Mamalis, A.G., Kundrak, J., Gyani, K. On the dry machining of steel surfaces using superhard tools, Int. J. of Advanced Manufacturing Technology, Vol.19, No.3. 2002, pp. 157-162

[21] Rech, J., Influence of cutting tool coatings on the tribological phenomena at the tool-chip interface in orthogonal dry turning, Surf. Coatings Technol., Vol.200, 200, pp. 5132-5139.

[22] Grzesik, W., Kiszka, P., Kowalczyk, D., Rech, J., Claudin, C., Machining of nodular cast iron (PF-NCI) using CBN tools, Procedia CIRP 1, 2012, pp. 483-487.

[23] Ghani, J.A., Othman, K., Rahman, M.N.A., Deros, B.M., Haron, C.H.C., Machined surface of FCD700 ductile cast iron in a dry turning environment using carbide tools, Int. J. Mech. Mater. Eng. (IJMME), Vol.6, No.3, 2011, pp. 362-366.

[24] Dudás, I.; Lierath, F.; Varga, G., Environmentally Friendly Technologies in Production Engineering, Dry cutting and the use of minimum volume of coolants and lubricants, Technical Publisher, Budapest, 2010, (In Hungarian)

[25] Sharma, A.K., Tiwari, A.K., Dixit, A.R., Effects of minimum quantity lubrication (MQL) in machining processes using conventional and nanofluid based cutting fluids: a comprehensive review, J. Clean. Prod., Vol.127, 2016, pp. 1-18.

[26] Giasin, K., Ayvar-Soberanis, S., Hodzic, A., Evaluation of cryogenic cooling and minimum quantity lubrication effects on machining GLARE laminates using design of experiments, J. Clean. Prod., Vol.135, 2016, pp. 533-548.

[27] Karkalos, N.E., Markopoulos, A.P., Computational Methods for the Assessment of Nanofluids in Abrasive Processes, Solid State Phenomena, Vol.261, 2017, pp. 201-206.

[28] Kundrak, J.; Mamalis, A.G.; Markopoulos, A., Finishing of hardened boreholes: Grinding or hard cutting? Mat. and Manuf. Process., Vol.19, No.6, 2004, pp. 979-993.

[29] N.N., AISI 1045 Medium Carbon Steel, https://www.azom.com/article.aspx?ArticleID=6130 (03.11.2018).

[30] Taguchi, G., System of experiment design, 1. Experimental design, UNIPUB, Kraus International Publications, White Plains, New York, 1987.

[31] Whitehouse, D.J., Handbook of Surface and Nanometrology, Second edition, CRC Press, Taylor and Francis Group, 2011.

[32] N.N.: Measurements of roundness error, Study aid, Taylor Hobson Precision, 2013, pp.: 1-34.

Cite this paper

Gyula Varga, Tibor Puskás, István Debreceni. (2018) Examination of Shape Error of Outer Cylindrical Surfaces Machined by Environmentally Friendly Way. International Journal of Mechanical Engineering, 3, 43-51

 

cc.png
Copyright © 2018 Author(s) retain the copyright of this article.
This article is published under the terms of the Creative Commons Attribution License 4.0